Staining Stair Treads

Staining Stair Treads Pre-finishing a set of stair treads before installation.

Step 1 Use a power sander and a medium-grade disc to sand the treads. Step 2 light scuff. Okay I know I said theres no sanding involved but it IS a good idea to do a. Also makes for a cleaner insta.

Outstanding Apply an additional coat if you prefer a darker stain.

Pick one and go with it. Go over the entire surface of each tread to start smoothing out the roughness of the wood1 X Research source Its necessary to sand the surface of your treads before doing anything else. How to Choose the Best Stain for your Wood. Inspect the wood observe whether the wood is ready for work or not Take action if its not ok.

Read Also : home modern stairs grill design  industrial spiral staircase  heavy duty carpets for hallways 

Allow the wood to dry thoroughly. Super

After that I feathered the stain in the same direction of the grain again. Removing the existing paint. Repeat sanding with 220 grit sandpaper once the tread has dried. Using a synthetic paint brush and 100 cotton to wipe off the excess stain worked best for me.

Prepare the place for the final work. Let dry for about 8 hours before using the stairs. Once your prep work is done strip the stairs by applying a chemical stripper for heavier stains or sanding the surface to remove a lighter coat of finish. Allow the stain to dry fully before applying a second and third coat.

Use a lint free cloth and cleaning solution if needed to wipe down floor treads and let dry. Save your money because nothing works better than an old clean 100 cotton t-shirt ripped up into 20 squares. Be sure to number your treads on the back so you get the right one in the right spot. Learn how to strip and sand your wood floors.

Remove all the old paint from the treads to prepare for sanding hardwood stairs. Personalize the look of your stairs. Step 1 clean the wood surface. This prevents down times due to multiple coats being applied on site.

Allow the stain to dry for 12 hours. There are two types of stain bases. Apply copious amounts of stain to make sure the wood is coated evenly. The treads arrive from the factory very smooth but its important to scuff the surface with fine 220-grit sandpaper to remove any oil or grime from the factory or shipping that might impede penetration of the stain.

Applying Paintstain In The Stairs. ONLY then proceed with the real stuff. Although water-based stains can be applied over an oil base but only after 24 hours or longer to ensure the oil-based stain is completely dry and no longer emitting dangerous fumes. Here are the few steps I took to stain the treads.

Fill any holes with wood filler or putty. Let it sit for a few minutes and wipe off the excess stain with a clean rag or old t-shirt. After your stairs have been stripped apply a coat of stain with a paintbrush or rag. Ready to refinish those tired old stairs.

I started at the corner of the treads. Make sure to go over the wood surface with a damp cloth to remove any residue of the cleaning solution because you dont want it to compromise your finish. Sanding and Dispossess old paints. Apply wood conditioner according to instructions optional Prep the area by laying painters tape around the stairs if desired.

Once the tread is again smoothed out apply the last coat of polyurethane. Great solution for wood stairs that are not high-quality woodstain-ready wood. Dont assume stains out of the can will be exactly as shown especially water based stains. By cutting them first we were left with off-cut pieces to test the stains on.

Adding the second layer if needed Guarding The Stairs. If you have low numbers of existing paint layers a heat gun will scrape away all the paint already on the stairs. Relatively easy way to makeover your stairs. After 24 hours check your stair treads.

We cleaned the stairs with a TSP alternative. Never mix the two. Sometimes you have to dilute the stain and sometimes you need two coats so stain a small sample AND apply the intended clear coat FIRST to see if you get the shade you are after. Leave tread to dry overnight.

Attach a medium-grade sanding disc to a power sander plug it in and turn it on. Can introduce lots of variety color patterns etc. Once tread has been completely finished store in a dry place from 24 hours with. Preparing The Staircase.

Apply the first coat of stain IN THE DIRECTION of the wood grain according to the instructions. Apply the stain liberally using a brush lint-free cloth or staining pad and then wipe the tread down using a lint-free cloth to remove any excess stain. Staining Stair Treads. Then I carefully dragged my brush along the edge of the tread and the stair stringer.

I feathered my brush towards the center parallel to the wood grain. Ed carefully measured each step and cut the tread to fit. I let my stairs dry for a full day before applying the coat of stain on the rest of the treads. Allow the stain to sit longer if you are hoping to have a darker stained-wood as a result.

Painted Stairs PROS. The stripping becomes simple if the amount of the paint layer is minor. Cut Stair Treads to Size. Check out the video series on Refinishing Wood Stairs.

No more slippery than stainedregular hardwood stairs. Let me give you a quick recap on how to stain pine treads. The longer you let it sit the darker it will be. I was using staining pillows at first which I bought from the hardware store.

Wipe the wood as you go for a lighter stain. This involved setting up a workstation of table space and drop cloths then sanding the Cherry wood surface of the treads. This is to be the thinnest coat and it is important to make the last coat as smooth as possible. Bring out further warmth by.