Installing Stair Railing Metal Balusters

Installing Stair Railing Metal Balusters Then gently wiggle the balusters back and forth until the nails holding them in place loosen and you.

I then took it all apart added glue and put it together again. Drill a 12 hole into the tread knee wall or landing tread. You drill a round hole install the iron baluster and leave it as is. Next screw the pivoting ball adaptor to the balusters corresponding location beneath the rail.

Impressive Drill the bottom hole to a depth of approximately 58 to 34.

When installing manufactured balusters drill the tread to accept the pre-made pins on the bottom of the baluster. Using a reciprocating saw or a jig saw cut the balusters in half. Slide the metal shoes on the baluster and tape the shoe up so that it is not in the way during installation. With the rail in its time to drill the bottom holes.

Read Also : woven stair treads  wire hand railing  wire stair railing diy 

The hole in the handrail will need to be at least 1 up into the bottom of the handrail. Fabulous

Please note that the standard shoes and pitch shoes do not add stability to the metal baluster installation the shoes are for cosmetic purposes and cover the gaps between the square baluster and the round holes. By the way if you read any real instructions on how to install iron balusters theyll. The turned top tip also allows the baluster to be installed without a metal baluster shoe underneath the handrail. Get the rail level and even before getting it tight.

Connect the rail using a rail bolt wrench. There will be exposed gaps around the balusters also meaning this is the most undesirable finished look. Cut out the old balusters. If this is a remodel rather than a new installation you will need to remove the existing wooden balusters.

Step 7 Epoxy Base Shoes. Drill the bottom hole to a depth of approximately 58 to 34. First slide your baluster shoe onto the baluster. Cut the metal baluster to length on a chop saw.

37-12 for your level run hand rail this is for handrails that are non staircase rails. The wood dowel and the metal baluster screw. If the stair handrail is screwed into place this wont apply but in either case you then insert the first baluster into the first hole with the opposite end of the stair rail lifted several feet above the upper balusters. You will repeat this for all of the iron balusters and then cut the bottom portion of each to length.

Slide the base collar over the baluster shaft and insert the upper tip of the baluster into the ball adaptor. Also drill a 1 12 deep hole into the underside of the handrail. To use the IronPro System first screw down the threaded metal discs at each baluster location. We purposely drilled out a deeper hole in top to give us this extra room.

Set the railing loosely on the newel post tenons and begin fitting the baluster tenons into the railing mortises beginning at one end and working towards the other. Measure the distance between the bottom of the handrail and the floortread surface. Take your first uncut iron baluster and place it upside down into its 58 hole then mark the length by adding about 1 up from the bottom of the stair handrail at the ¾ hole. For commercial code cut to 42 and set rail height a bit over 43 just to be safe once again we always recommend you consult your local building inspector in your city.

You will only need to drill 12 or 916 holes depending on which size baluster you are using. Once all the fillet strips and spindles were put in the shoe rail I trimmed the end fillet strips to ensure a tight fit. About 2 12 inches will usually do. Then taking the handrail and starting at one end the bottom of a stair balustrade you set it in place with the rail bolt through its hole.

If a factory turned dowel is not available there are two basic types of dowels that may be added to your baluster. Slide the baluster into the top handrail first and then drop it down into the hole in the floor tread. Square up the sides of the holes with a chisel after drilling. Whether you are doing new installation or replacing old balusters you need to ensure you have holes at the appropriate sizes and depths.

You can also set the rail to. Once you have cut the balusters this will allow you to slide the baluster into the handrail fi rst and then drop it down into the bottom mounting hole Measure the distance from the bottom of your handrail to the top of the tread where your baluster will be placed Baluster Hole Diameter º ½ Balusters use a 5 8 wood bit º 9. 4 Steps For Installing Metal Balusters. Our powder coated metal balusters have the top of the baluster turned round which will may allow you to use a smaller diameter drill bit for the top hole.

Dont be shy with the hot glue friends. Apply yellow wood glue to the ends of the railing. Make sure everything lines up and the pattern is correct before adding glue. After you fit all the balusters into the railing look over the installation to make sure it looks good.

Cut the balusters 1-38 to 1-12 longer than the measured distance. I use a laser to transfer the location to the floor. Cut The Metal Balusters. Round hole with Epoxy Only This is easily the fastest method.