Measuring Hall Stairs And Landing For Carpet

Measuring Hall Stairs And Landing For Carpet You need to measure the widest point of the hall taking into account doors on walls dont forget to add any measure for drop backs into doorways or alcoves.

Note where the stairs enter the hall. Free shipping on all orders every day. Some carpet installers will charge by the stair at 310for a basic set of box stairsor 515 per stair if you have spindles from a handrail. This will be explained in more detail later.

Impressive Save with wholesale prices on all rugs.

To figure out if your budget covers your options youll likely want to know how to measure stairs for carpet. Shop with iRugs today to save big. When finalising the measurements for your stairs and landing carpets its always a good idea to add at least 3M2 and possibly more so that youve got a little leeway. In general you can measure stairs for carpeting by using the equation width x run rise nose x number of stairs area.

Read Also : mezzanine floor stairs design  modern black spiral staircase  modern home railings 

Free shipping on all orders every day. Beautiful

1The first step you can do is to measure the landings both at the top and the bottom of the stairs. It is typically approximately 3 wide. Firstly draw a simple plan of the Hall to put your sizes on. Ad Colors and styles for every room in your house.

Note were the stairs meet the hall. Multiply that measurement by the number of stairs that you have providing they are all the same type of shape. 772 16 inches. Note the arrow pointing down the stairs into the landing.

The width of the carpet has to be rounded up to 4 or 5 metres in width depending on the carpet. If the stairs are open on the side then the carpet must be bent in two ways. As a rough starting point a 4m wide carpet would cut into 2 sections 2m wide to do the hall and landing so to do the hall youd need it to be 475 long. Dont let this economic wave pass you by.

Was 16 99 sqm Sale 11 99 sqm. When measuring stairs for carpet remember to take the risers and the lip on. Measure the stair width normally between 76cm and 93cm Book A. Take your maximum dimensions only remember to measure into doorways.

This is the length vertically up and over the step. This will be explained in more detail later. If all of your stairs are the same width you will only need to measure one. Draw a floor plan of your landing and hallway then mark with an arrow where the stairs come down from the landing.

Add a minimum of 5cm 2 inches to the total width allowing for any waste. This is a very important point to remember when measuring anything involving stairs. Next measure the tread riser and the width of the stairs. Save with wholesale prices on all rugs.

The prospect of measuring your home for new carpet or flooring can be a daunting one especially when it comes to the tricky hall stairs and landing area. This is the total area or square footage for the stairs you plan to carpet. However with a bit of planning some insider knowledge and the right tools the internal measuring Stanley Powerlock Top Reader tape is ideal it really is a very straightforward task. Ensure that you have the right measurements from the doors threshold across the landing and also down the nosing to the first.

STEP 2 - Measuring Stair Width. A durable carpet which is ideal for all areas of your home. Measuring your own rooms for fittings can definitely save a lot of money but always make sure youre confident in your measurements before ordering underlay and carpet. However calculating how much carpet you need varies based on the stair type shape and size as well as the configuration of your staircase.

This can be achieved by the use of a tape measure. Therefore for every box stair you require 3 or the width of your stair x 18 of carpet. You should start by measuring the length and width of the hallway as you can see from the plan to the right. Make sure when measuring the landing that you measure from the threshold of the door across the landing and over the nosing down on to the first step.

Multiply the square footage of 1 stepthe number you just calculatedby the total number of steps. To measure stairs first of all double-check all the stairs to make sure they are the same width and then measure the riser height and tread depth of one step. Count the number of stairs. Round your measurement up to the nearest inch or cm.

You would need the widest part of the landing along with the first tread and the longest bit. For a stairwell with 13 stairs and one landing. Then measure the distance from the wall to the foot of the stairs. Hold the measuring tape flat against the tread of the stair put the end of the measuring tape against.

7 inches for each rise and run plus two inches for the nose and overage. Always add 5cm 2 minimum to both the length and width of the carpet measurements. Part of the series. 208 inches12 1733.

Note the arrow pointing down the stairs into the landing. You need to measure the stairs taking into account the tread and the riser. Remember to measure into doorways and to maximum points in the hall. Lengthwise over the front of the stair and widthwise over the side.

The usual allowance for the tread the flat part you step on is 10 and 8 for the riser the back of the stair. How to measure stairs and landing. Make sure to measure any drop backs or. Say that youll be carpeting 12 stairs.

16 inches x 13 stairs 208 inches. Measure the tread and the riser marked A on the diagram 3. Next measure your hall as if it was a square room. In these cases there is the possibility of smiling to occur on the side of the stair.

There is no need to measure the length of the stairs simply follow the method below for a simple staircase. Measure the width and depth of the doorways of your landing and hallway and jot down this information on your plan. This is a very important point to remember when measuring anything involving stairs. Measure from the top of the stairs to the bottom as this is the way the pile direction will go.

Home Construction Remodeling. Take your maximum dimensions only remember to measure into doorways. How to Measure Stair Carpet. See drawing the same applies to the narrowest width.

However to do 12 stairs at 10high 25m and 9front to back 225m you would need 57 metres at about 085m wide. Make sure when measuring the landing that you measure from the threshold of the door across the landing and over the nosing down onto the first step. In our example youd need a total of 96 square feet 89 m 2 of carpeting to cover your stairs. Turn your tape measure 90 degrees and measure the depth of the stairs.

Start your measure from the hallway. Long Lasting Luxury Range. Ensure that you note the meeting point of the stairs and the hall. Now 10 49 sqm.